• 검색 결과가 없습니다.

Effect of operating conditions on carbon corrosion in High temperature polymer electrolyte membrane fuel cells (HT-PEMFCs)

N/A
N/A
Protected

Academic year: 2021

Share "Effect of operating conditions on carbon corrosion in High temperature polymer electrolyte membrane fuel cells (HT-PEMFCs)"

Copied!
1
0
0

로드 중.... (전체 텍스트 보기)

전체 글

(1)

연료전지<<89

고온형 고분자 전해질막 연료전지(HT-PEMFC) 구동환경에 따른 탄소 담지체 부식 평가

*이 진희, **김 한성

Effect of operating conditions on carbon corrosion in High temperature

polymer electrolyte membrane fuel cells (HT-PEMFCs)

*Jinhee Lee, **Hansung Kim

The influence of potential and humidity on the electrochemical carbon corrosion in high temperature polymer electrolyte

membrane fuel cells(HT-PEMFCs) is investigated by measuring CO2 emission at different potentials for 30 min using

on-line mass spectrometry. These results are compared with low tempterature polymer electrolyte membrane fuel cells(LT-PEMFCs) operated at lower temperature and higher humidity condition. Although the HT-PEMFC is operated at

non humidified condition, the emitted CO2 in the condition of HT-PEMFC is more than LT-PEMFC at the same potential

in carbon corrosion test. Thus, carbon corrosion shows a stronger positive correlation with the cell temperature. In addition, the presence of a little amount of water activate electrochemical carbon corrosion considerably in HT-PEMFC. With increased carbon corrosion, changes in fuel cell electrochemical characteristics become more noticeable and thereby indicate that such corrosion considerably affects fuel cell durability.

Key words : Carbon corrosion(탄소부식), Mass spectrometry(질량분석), Durability(내구성), High temperature

polymer electrolyte membrane fuel cell(고온형 고분자 전해질막 연료전지)

E-mail : *[email protected], **[email protected]

고분자 연료전지의 데드엔드 운전 시 기울임에 따른 성능 변화

*,**정 지훈, 고 백균, 한 인수, 신 현길, 허 태욱, 조 성백

The Effects of the Inclination on the Performance of dead-end operating PEM Fuel Cell

*,**Jee Hoon Jeong, Back Kyun Kho, In-Su Han, Hyun Khil Shin, Tae Uk Hur, Sung Baek Cho

In automotive applicatons or water vehicles, the polymer electrolyte membrane fuel cell(PEMFC) stack is keep moving while their operation. Especially the inclination environment can take a effect to fuel cell stack perfromance, because this condition can cause a bad effect to water exhaust of fuel cell stack.

In this study, a large scale stack(over 100kW power) is inclined upto 30 degree in lengthwise and crosswise using stack lift equipment. And the stack is operated in 10~100% load.

No significant change has appeared in crosswise inclined condition and lenthwise low angle. But in lenthwise large angle tilting condition, the fuel cell performance has significantly decreased. And this performance decrease is aggravated in low load.

An active water exhaust device is applied to the stack to prevent the performance decrease. And in lenthwise large angle tilting condition, this device cause a good effect to fuel cell stack performance.

Key words : PEMFC(고분자연료전지), Fuel Cell(연료전지), Inclination(기울임), Dead-end operation(데드엔드 운전),

Performance(성능)

참조

관련 문서

7 Effect of annealing temperature on the tensile properties of high manganese austenitic stainless steel with two phases of reversed austenite and

The aim of this study was to compare the effect on bone regeneration relative to maintenance period of PTFE membrane in rabbit calcarial defects.. Eight adult

The used output data are minimum DNBR values in a reactor core in a lot of operating conditions and the input data are reactor power, core inlet

본 실험에서는 불소이온의 흡착능력을 증대시키기 위하여 대나무 탄화물 제조를 다르게 하였다. Effect of temperature of heat treatment on the adsorption of F - by

이후 steam/carbon 비가 증가함에 수증기량의 증가로 인한 따라 점차적으로 농도가 감소됨을 알 수 있다... Effect of various steam/carbon ratio

Yanga, “Mesoporous activated carbon fiber as electrode material for high-performance electrochemical double layer capacitors with ionic liquid electrolyte”, J...

pottery, tableware, cookware, building materials, aerospace materials, to nuclear materials (e.g., UO 2 pellets, waste forms, etc.)... A’ a’ B’ b’ C’

- The basic materials were Reinforced Carbon-Carbon, Low- and High-Temperature Reusable Surface Insulation tiles, and Felt Reusable Surface Insulation blankets.. -