BERNARD G. DAGATAN
ELECTRICAL ENGINEER, LICENSE No. 5888
PROFESSIONAL QUALIFICATION
· Registered Electrical Engineer with combined exposure in Engineering Design, construction, testing, commissioning, operation and maintenance of Electrical, Instrumentation and Communication system.
· Computer literate with basic knowledge on AutoCAD.
FIELD OF INTEREST:
Electrical & Instrumentation (Engineering, Construction & Maintenance)
________________________________________________________________________
EMPLOYMENT RECORD
COMPANY : Kellogg Brown & Root (KBR) PROJECT : SHELL Pearl Gas to Liquid (GTL) ADDRESS : Ras Laffan Industrial City, Qatar POSITION : Instrument Supervisor
PERIOD COVERED: July 18, 2008 to Oct 28, 2008 DUTIES AND RESPONSIBILITIES:
• Work supervision for the installation of different process instrument, fire and gas
detectors, and ensure that correct instrument to be installed complies with the approved specification and quality standard.
• Coordinate with the other Implementation Contractors representative regarding interface work outside battery limits.
• Complete work in accordance with Engineering Quality System requirement by following procedures and work instruction. Complete checklist or other documents required during work execution. Proposed changes to procedures, works instruction, methods and plant equipment modifications, with the aim of continuous improvement.
• Ensure that Total Safety Task Induction (TSTI) has been conducted before the works starts then validate the daily TSTI. Also ensure the daily Permit to Work (PTW) is validated by the authorized personnel.
COMPANY : HYUNDAI HEAVY INDUSTRIES, Nigeria Limited
PROJECT : Bonny Terminal Integrated Project, BTIP ON-SHORE Facilities SHELL Petroleum Development Company (SPDC) of Nigeria Ltd.
ADDRESS : Bonny Island, River State, Nigeria POSITION : Instrument Design Engineer PERIOD COVERED: October 04, 2006 to June 05, 2008
DUTIES AND RESPONSIBILITIES:
• Prepare loop diagram and block logic diagram for Process Automation System (PAS), Safety Instrumented System (SIS) and Fire and Gas System (FGS). Reference used are Process Engineering Flow Scheme (PEFS) drawing, I/O list, vendor documents and interconnection diagram with minimum supervision of System and Control Engineer.
• Design typical installation drawing such as instrument stanchion, junction box installation, hook-up drawing, etc… with the guide and familiarization of Shell Design and Engineering Practice (DEP).
• Site inspection and prepare design changed notice for review to SPDC if required some changes to modify with regards to actual site condition/installation and the approved for construction drawing.
• Site inspection and prepared all instruments as built drawings and equipment data book for final submission to client (SPDC).
• Modification of interconnection drawing and cable schedule based on the vendor documents and latest I/O list, and awareness of the Foundation Fieldbus Technology design concept.
• Data input of all the changes and link the appropriate tags of different instrument, cable, junction box, equipment, etc., to its subsystem on the WIN PCS, a windows Project Completion System monitoring device. Coordinate with the QA/QC representatives regarding WIN PCS changes.
• Work supervision for the installation of different process instrument, fire and gas detectors, and ensure that correct instrument to be installed complies with the approved specification and quality standard.
• Complete work in accordance with Engineering Quality System requirement by following procedures and work instruction. Complete checklist or other documents required during work execution. Proposed changes to procedures, works instruction, methods and plant equipment modifications, with the aim of continuous improvement.
• Performed joint inspection with SPDC representative for pressure/leak test for instrument air line connected to different pressure control valves, shut down valve, level control valve, analyzer, GTG, etc..
• Monitoring work progress done and prepare documentation for the items that need pre- inspection and attend joint inspection with the QC inspector and SPDC representative for mechanical completion acceptance.
COMPANY : NITRO Construction and Engineering ADDRESS : Bigain San Jose, Batangas, Philippines POSITION : Electrical Engineer
PERIOD COVERED: November 05, 2002 to May 12, 2005
DUTIES AND RESPONSIBILITIES:
• Designed new electrical installation and works supervision of it.
• Installation, repair and maintenance of various electrical equipments of different establishments.
• Installation of telephone and televisions system.
• Electrical rehabilitation works of different houses and buildings.
• Installation and repair of different air-conditioning units and water heaters.
• Ensure that all connected wires and safety devices are within the specification
• Prepares quotation and customer billing base on the percentage of accomplishments.
• Materials take off, estimates and preparation of as built drawings.
COMPANY : NEC System Integration and Construction Pte. Ltd., Singapore PROJECT : Mass Rapid Transit (MRT) - Northeast Line Communication System ADDRESS : 122 Middle Road, #02-06 Midlink Plaza, Singapore 188973
POSITION : Testing and Commissioning Engineer PERIOD COVERED: May 02, 2001 to July 20, 2002
DUTIES AND RESPONSIBILITIES:
• Responsible for testing and commissioning of Facility for Commercial Service’s (FCS), Tunnel amplifier, master site fiber optic interface unit (MSFOIU), master site signal distribution unit (MSSDU) for high band GSM 1800 and low band GSM 900. (Test Equipment: RF Signal Generator, Spectrum Analyzer).
• Post installation testing of station and tunnel LCX cables using VSWR and Insertion Loss Testing, and prepare link budget calculation base on actual installation of LCX cable for FCS and Radio Communication System (RCS). (Test Equipment: Anritsu Site Master 332A, 332B, 332C, and Signal Generator).
• RF coverage testing of station and tunnel for FCS and RCS.
• Troubleshoot and rectify LCX installation if found a weak signal coverage of a specific area.
• Integration testing and commissioning of RCS (Tetra and SCDF/SPF) and FCS with Train Borne System using low speed and high speed. (Test Equipment: Chase GPR Receiver 4403/4403A with Hindsite Software, Grayson wireless Receiver with WMS software and monitored by Site Master Spectrum Analyzer).
• Insulation and continuity testing of power system cable.
• Station to station testing of fiber optic cable using optical power meter.
• Preparation of test reports gathered.
• Supervision of LCX installation for six stations in section 1, which was done in parallel.
• Project planning and manpower scheduling.
• Coordination with the main contractor and other system wide contractor regarding LCX issue and installation clashes.
• Interface connection of GSM 900 and GSM 1800 combiner to MMDC panel.
• Uplink interface with the three operator’s base station (M1, Singtel and Starhub) for GSM 1800.
• Materials take off, estimates and preparation of as built drawings.
COMPANY : Self-Employed ADDRESS : Batangas City, Philippines POSITION : Electrical Engineer PERIOD COVERED: January 1999 to April 2001
• Designed new electrical installation and works supervision of it.
• Installation, repair and maintenance of various electrical equipments of different establishments.
• Electrical rehabilitation works of different houses and buildings.
• Installation and repair of different air-conditioning units.
• Installation of various electrical materials and equipment of a particular project with approved plan and specification.
• Ensure that all connected wires and safety devices are within the specification
• Thorough knowledge in troubleshooting, operation and maintenance.
• Accredited Trade Testing Officer (Assessor) for Refrigeration and A/C Technician – Technical Education Skills and Development Authority (TESDA, Batangas City, Philippines).
COMPANY : Marconi Communications (GEC Hong Kong Limited) PROJECT : MTR-Lantau and Airport Railway Communication System ADDRESS : 27/F CC Wu Building, 302-308 Hennessy Road,
Wanchai, Hong Kong
POSITION : Testing and Commissioning Engineer PERIOD COVERED: January 6, 1998 to October 25, 1998 DUTIES AND RESPONSIBILITIES:
• Report directly to our project supervisor regarding our project instruction and accomplishment report.
• Testing and commissioning of electrical power supply system for electrical and communication services.
• Installation of electrical panel board and cable termination to its scheduled equipment.
• Installation and fabrication of cable tray, cable ladder, conduit and its supports.
• Estimate and requisition of spare parts and tools needed for maintenance.
COMPANY : Rotary International Limited (Hong Kong) PROJECT : Hong Kong International Airport
ADDRESS : Chek Lap Kok Island, Hong Kong POSITION : Electrical Technician
PERIOD COVERED: September 21, 1996 to November 21, 1997
DUTIES AND RESPONSIBILITIES:
• Testing and commissioning of electrical lightings and power system.
• Prepare as built drawings.
• Installation and fabrication of conduits, cable ladders, cable trays, cable trunking and its supports.
• Installation of electrical lighting devices, switches, power outlets, sensors and other electrical components.
• Cable pulling, cable glanding, cable testing and termination to panel/equipment.
• Installation and fixing of electrical control panel boards.
COMPANY : Hundt Weber Electric Philippines Corporation ADDRESS : Suite 2401 Cityland 10 Tower 1
6815 H.V. dela Costa St. Makati City, Philippines POSITION : Technical/AutoCAD Engineer
PERIOD COVERED: January 10, 1996 to September 16, 1996
DUTIES AND RESPONSIBILITIES:
• Designed detailed drawing of different types and ratings of Automatic transfer switch (ATS), Synchronizing panel (manual/automatic), motor control center (MCC), main distribution panel board, capacitor bank, and other electrical components as per customer requirements using AutoCAD R12.
• Provide technical support for company Sales staff regarding products lines.
• Fabrication, assembly, installation, servicing of the above electrical products.
• Preventive maintenance of the electrical products been installed for its warranty period.
COMPANY : Armed Forces Hospital King Abdulaziz Airbase ADDRESS : P.O. Box 570 Dhahran Airport, K.S.A.
POSITION : Electrical Technician PERIOD COVERED: July 12, 1992 to July 11, 1995
DUTIES AND RESPONSIBILITIES:
• Performed duties as defined in electrical engineering and maintenance department.
• Evaluates technical problems related to electrical maintenance.
• Performed preventive inspection and maintenance of electrical panel boards, motors, generators, batteries, uninterrupted power supply (UPS), low-tension switchgear, pumps and different electrical equipment.
• Responsible for electrical renovation works, expansion and maintenance of hospital buildings and employees accommodation.
• Estimates the material needed for new installation works.
• Repair different types of domestic appliances such as buffing machine, clothes dryer, washing machine, vacuum cleaner, electric stove, dishwasher, fan, blower, etc.
• Inspect, test and repair various electrical equipment such as motor, generator, pumps, automatic door, control panel board for A/C unit, boiler, motor control center (MCC).
• Installation, troubleshooting of fire alarm system.
• Operates various electrical testing equipments.
• Performed other related duties as assigned.
COMPANY : Dragon Enterprises Corporation (Reynolds) ADDRESS : #44 Libertad St. Pasay City, Philippines POSITION : Staff Engineer
PERIOD COVERED: March 5, 1992 to June 25, 1992
DUTIES AND RESPONSIBILITIES:
• Ensure safe and continuous operation of the building electrical distribution and related components.
• Section In-charge for the automatic assembly of Reynolds ball pen by using electro- pneumatic machine.
• Maintain emergency generator in good running condition.
• Preventive inspection and maintenance of different machine and equipment for its efficient use.
• Installation of additional machine needed by the company.
EDUCATION AND UP-GRADING TRAINING/SEMINARS
BACHELOR OF SCIENCE IN ELECTRICAL ENGINEERING (1985-1990) Batangas State University, Batangas City, Philippines (formerly PBMIT)
INDUSTRIAL ELECTRICITY (July 28 to September 17, 1990) National Manpower and Youth Council, Philippines
SUPERVISORY DEVELOPMENT COURSE (Bldg. Electrical Construction Works) Construction Manpower Development Center
